Next Previous Contents

5. xtpconfig - the config menu (LPR)

With the xtpconfig program you can select all the options you may want to change before printing a document. This includes settings like print quality, type of paper, etc.

Note:TurboPrint can be integrated in the two different printing systems LPR/LPRng and CUPS. Depending on which system is installed on your Linux OS xtpconfig offers different settings. In this chapter we assume that you are using the LPR printer spooler system. Should you have installed the CUPS printing system please skip to the next chapter.

xtpconfig menu

The config menu has several menu pages each containing a group of settings that belong together.

Available pages are:

Printer

Select the configuration and set paper type, quality

Paper

Paper size, tray, multiple copies, zoom

Graphics

Settings for brightness and color rendering

Image

Size and position settings for image printing

Toolbox

maintenance utilities mainly for inkjet printers

In the bottom line there are four buttons that will be available from all menu pages:

Save

Save the changed settings and leave the config menu

Apply

Save the changed settings but don't leave

Cancel

Quit the config menu and forget all changes that have not yet been saved

Info

Display some information about TurboPrint.

After starting the config menu the "Printer" page is shown. The first thing you have to do is to select the configuration for which you want to change the settings:

In the "Choose configuration" field there is a table shown which lists all available printer configurations that are currently installed. Select the desired configuration by clicking on its name. All settings that you change from now on will be changed in the selected configuration. The changes do not get into effect until you press either Save or Apply.

In the following you find the different menu pages and its settings:

5.1 Page "Printer"

A table is shown that lists all available printer configurations installed by TurboPrint (with xtpsetup).

xtpconfig - printer

Choose the appropriate configuration whose settings you want to change in the configuration list.

For each printer configuration, the following entries are displayed:

Configuration

This is the configuration's name. A ">" is shown in the leftmost column if this configuration acts as the default printer.

Short

A short name (alias) for the printer Configuration

Connection

The device that the printer is attached to (or the name of a remote printer).

Printer

The name of the printer model and the corresponding printer driver.

Note that there can be several configurations for the same printer. So you can e.g. have a configuration for printing images and one for printing office letters. Select the desired configuration by clicking on its name.

Below the configuration table you find four basic settings for your printer:

Quality

Almost every printer offers different print modes. Normally, the higher the print quality is the longer the printout will take. So you will probably choose a lower print quality for draft and test printouts and one of the highest qualities for the final printout.

Note: In TurboPrint FreeEdition, some print modes are marked with an arrow at the left. These work only in demo mode, i.e. that a TurboPrint logo is added in the upper right corner of the printout. To use TurboPrint as full version please purchase a license with a personal keyfile at www.turboprint.de.

Cartridge

Some ink jet printers have separate exchangeable ink cartridges for black or color printing. If this is the case with your printer you have to tell your printer driver which cartridge is currently installed (e.g. Black, Color, Photo) so that it can make use of the available colors.

Paper

Choose the kind of paper you want to print at. This is especially important for ink jet printers. Depending on the paper quality (e.g. normal paper, photo paper, glossy paper, etc.) the printer driver varies the amount of ink per area and uses special color correction modes. If you set the wrong type of paper you may get a bad print quality. Depending on the printer different choices are available.

Note: In TurboPrint FreeEdition, special papers are marked with an arrow at the left. These can only be used in demo mode, i.e. that a TurboPrint logo is added in the upper right corner of the printout. To use TurboPrint as full version please purchase a license with a personal keyfile at www.turboprint.de.

Color Mode

This setting defines how TurboPrint will adopt the colors for the printer.

Black & White

Means that there are no colors at all. For postscript documents, shades of gray will be generated by ghostscript. If images are printed, any color that will be printed becomes either black or white depending on its brightness.

This mode is fast and recommended for printouts without color or gray shades (just black text, no images). It is the default for black & white printers.

Grayscale

256 Levels of gray - used for printing color images in black & white.

Truecolor

24bit color. This is the default setting for color printers.

256 Colors

8bit color (equals to 256 different colors) - less print quality but sometimes faster printouts than with "24bit". Use this for color text documents or clipart graphics with few colors, not for photorealistic images.

Info

This field displays the currently selected print mode with additional information like dpi ("dots per inch") or special print modes.

5.2 Page "Paper"

xtpconfig - paper

Pagesize

The paper size, e.g. Letter, A4, etc.

Feed

The input feed (e.g. manual or automatic).

Tray

The output tray (only for printers that support different output trays).

Duplex

Only for printers that support duplex printing. Activate "Duplex" mode if you want the printer to use both paper sides.

Copies

If you want get several copies, enter the desired number of printouts ("1" means no copies).

Mirror

The printout will be mirrored (left and right swapped). This setting is activated automatically for "backprint" and "t-shirt transfer" media.

Zoom

You can scale up or down the printout. The entered value is the factor by which width and height are changed.

  .........
 /|\      .
  |       .
  |   printout is zoomed to the right & top
  |       .
  |       .
  o-------> bottom left corner is fixed

100% = original size. E.g. use "141%" to double the size of the printout.

X-Offset

Change the horizontal position of the printout. Positive values: move to the right. Negative values: move to the left.

Y Offset

Change the vertical position of the printout. Positive values: move printout to the top. Negative values: move printout to the bottom.

5.3 Page "Graphics"

The following settings contain adjustments for the reproduction of brightness and colour.

xtpconfig - graphics

TrueMatch Color Correction

Switches the powerful TrueMatch colour correction on/off. This system developed for TurboPrint will allow you to accurately output to your printer what you see on the screen. Every single screen colour will be adjusted separately according to the used printer and kind of paper. TurboPrint comes with special colour correction tables for many kinds of paper and almost every printer on the market.

Dithering

While your screen can display millions of colours, your printer normally only supports black or four (some printers even up to eight) different colours. It is therefore necessary to create intermediate colours or shades of grey either by mixing the ink colours and/or by applying certain dithering patterns to produce the illusion of more colours than the printer actually uses. To accurately represent the on-screen colours, TurboPrint supports two different dithering patterns:

Error Diffusion

This diffuse pattern tries to eliminate any visibly noticeable geometrical pattern. As the distribution of the dots requires a lot of processing power, the printout time is higher than with the Ordered pattern.

Ordered

The dot pattern is equivalent to those used for newspapers printing. In this mode printouts are not as smooth as with the Error diffusion pattern but significantly faster.

Activate User Colors

Switch on/off the subsequent adjustments. There are two groups of color correction sliders. By pressing the "Standard" or "Advanced" button you make the corresponding group of settings visible.

Standard (first group of color settings)

Brightness

Use this slider to render the printout lighter or darker.The higher the value the brighter your printouts will get. Range: -50..50, default: 0

higher brightness -> brighter printouts
lower brightness  -> darker printouts
   

Contrast

Use this slider to increase or decrease the contrast of your printout. Range: -50..50, default: 0

higher values -> increase contrast
                 (dark colors get darker, bright colors get brighter)
lower values  -> decrease contrast
   

Color Saturation

Change the color saturation. Range: -50..50, default: 0

higher color saturation -> more vibrant colors
lower color saturation  -> less vibrant colors
   

Screen Gamma

Attention: Use this setting only if you want to adjust the brightness of printouts to the currently used monitor and / or scanner!

The slider lets you modfy the brightness according to the Gamma function (y=x^gamma). This will allow you to change the intermediate brightness values, without changing the extremes, i.e. pure black will still remain pure black on the final hardcopy, and white will remain white. Set the slider to the gamma value of your monitor. The default value is 180 (gamma=1.8) which is also the default for most scanners.

Higher gamma value -> darker printouts
lower gamma value  -> brighter printouts
   

Advanced (second group of color settings)

Ink Saturation

Change the amount of ink applied

(range -50..50, default 0).

Attention: If too much ink is applied, ink won't dry properly and may smear.

Yellow

The amount of yellow ink applied (range -50..50, default 0).

higher value -> use more yellow ink
lower value  -> use less yellow ink
   

Magenta

The amount of magenta ink applied (range -50..50, default 0).

higher value -> use more magenta ink
lower value  -> use less magenta ink
   

Cyan

The amount of cyan ink applied (range -50..50, default 0).

higher value -> use more cyan ink
lower value  -> use less cyan ink
   

Black

The amount of black ink applied (range -50..50, default 0).

higher value -> use more black ink
lower value  -> use less black ink
   

5.4 Page "Image"

The settings in this menu page determine the print size and position of images. This is only used if bitmap images (e.g. PBM, PPM, BMP, GIF, JPEG) are directly printed from command line with lp oder lpr.

xtpconfig - image

Paper Info

This box gives imformation about the dimensions of the chosen paper. Normally printers cannot print at a small border of the paper (indicated as "Unprintable borders"). So the maximum print area (indicated as "Printable region") is a bit smaller than the paper size.

Size

Set image width and height. If the image height is set to zero, it will be calculated from the image width according to the image proportions.

Keep aspect

Check this button to keep the image proportions. It will be printed at the maximum size within the bounding box determined by height and width, keeping the original aspect ratio intact. I.e. either height or width will be reduced if necessary.

Position

"Left" and "Top" indicate the position of the printed image measured from the top left edge of the printable area. Note: If you want to measure the margins from the paper borders you have to subtract the top and left unprintable borders (indicated at the left menu side in "Paper Info").

Center X, Center Y

If the "Center X" and/or "Center Y" checkbutton is activated the image will be centered horizontally and/or vertically on the page.

5.5 Page "Text"

These are settings for the layout of simple ASCII text documents. a2ps is used for formating ASCII text. If a2ps is not installed, enscript will be used instead.

xtpconfig - text

Use A2ps / Enscript Parameters from defaults / xtpconfig

This switch decides whether the default settings of a2ps (or enscript) or the settings of this menu page will be considered for simple ASCII text printouts. If you choose "defaults" then the following settings will be made inactive (ghosted).

Orientation

This defines the print direction with respect to the physical page. Choose "Portrait" for using the "upright" direction (normal way) or "Landscape" for printing rotated by 90 degrees on the page.

No. of Columns

Specify the number of text columns on the page.

Print Borders

Check this button if you want to have borders printed around your page / columns.

Print Header

Optionally, a header gives information about your documents title, pagenumber, etc.

5.6 Page "Toolbox"

The Toolbox is used for maintenance jobs with mainly ink jet printers. It can carry out tasks like nozzle check, head cleaning, head alignment, ink quantity check, etc.

xtpconfig - toolbox

There may be some jobs which are not supported by your printer. The corresponding buttons are "ghosted" then.

The following tools are available and can be accessed by pressing the corresponding button:

Testpage

Print a testpage. This is useful to check if the printer is working and is properly connected to the computer. Additionally, for a correct printout the appropriate printer driver must be selected.

Set Alignment

Align the black & color print heads and/or align bidirectional printing. The alignment procedure depends on the printer manufacturer and model. Usually a page with several lines of test patterns (lines, crosshairs) is printed. For each line, the number of the pattern with the best alignment is requested and must be entered (e.g.the pattern where two lines align best).

Please just follow the directions given by the "Alignment" tool.

Nozzle check

Prints a nozzle check pattern. This requires one page of paper. For each color a "staircase pattern" is printed. If one or several steps of the "staircase" is missing or smeared, the print heads should be cleaned (see next tool).

Clean print heads

Clean the print heads. This may consume some ink (like printing one or several pages), so cleaning should only be done if really necessary.

Check Ink quanitity

Show the remaining quantity of ink in the cartridges (only available for some printers). The amount is displayed separately for each ink color. 100% means the cartridge is full. You need to be logged in as "root". This is because TurboPrint has to access the parallel port directly. Otherwise the "Ink quantity" tool is not available.

Attention: You can temporarily change to superuser-mode by the "su root" command from shell. Sometimes it is not possible to start a GUI program then. If this should be the case you will have to configure the XWindow system for the new user by the following shell commands:

xhost +
su root
export DISPLAY=:0
xtpconfig

Change Ink cartridge

This function is only available for some printers where the ink cartridge can't be exchanged without a control program. Please follow the instructions given by xtpconfig. You need to be logged in as "root". This is because TurboPrint has to access the parallel port directly.

5.7 Page "Info"

The info page contains information on the TurboPrint version (version number, copyright notice) and license status:

xtpconfig - Info

FreeEdition, unregistered

Before you have purchased a license with a personal keyfile.

To use TurboPrint as full version please purchase a license with a personal keyfile at www.turboprint.de.

registered

After you have added your personal keyfile and reinstalled TurboPrint.

Should you already have bought a license, please follow the instructions that came with the keyfile and reinstall.


Next Previous Contents