Broadcom 802.11 Wireless Network Drivers
Release 3.100.41.0

Broadcom Corporation Confidential.
For Evaluation Use Only.

System Requirements

Software (supports the following operating systems):

Windows XP
Windows XP SP1
Windows XP SP2
Windows 2000 SP4

Hardware:

Minimum configuration: Pentium 300 MHz, 128 MB RAM.
Broadcom BCM94301MP Mini-PCI Reference NIC -or-
Broadcom BCM94301CB Cardbus Reference NIC -or-
Broadcom BCM94301PC PCMCIA Reference NIC -or-
Broadcom BCM94306CB Cardbus Reference NIC -or-
Broadcom BCM94306MP Mini-PCI Reference NIC -or-
Broadcom BCM94306CBSG Cardbus Reference NIC -or-
Broadcom BCM94306MPSG Mini-PCI Reference NIC -or-
Broadcom BCM94306MPGP Cardbus Reference NIC -or-
Broadcom BCM94301+2050 Mini-PCI Reference NIC -or-
Broadcom BCM94309CB Cardbus Reference NIC -or-
Broadcom BCM94309MP Dualband Mini-PCI Reference NIC -or-
Broadcom BCM94318MP Dualband Mini-PCI Reference NIC -or-
Broadcom BCM94318MP Mini-PCI Reference NIC -or- vendor equivalent.

Included in This Release

NDIS 5.1 miniport driver
Driver supports required Windows XP wireless OIDs for zero configuration and administration
Broadcom configuration tray application extended to support a similar interface as Windows XP on Windows 2000, Windows ME, and Windows 98SE

Hardware and Interoperability Test Matrix

Laptops (MiniPCI)
- Apple Powerbook G4 54Mbps AirPort Extreme
- Dell Latitude C400
- Dell Latitude C600
- Dell Latitude C610
- Dell Latitude C640
- Dell Latitude C810
- Dell Latitude C840
- Dell Latitude X200
- Dell Inspiron 4100
- Dell Inspiron 4150
- Dell Inspiron 5100
- Dell Inspiron 8100
- Dell Inspiron 8200
- Gateway M405
- Gateway450ROG
- IBM ThinkPad T23
- IBM ThinkPad A30
- IBM Thinkpad A31
- Toshiba Tecra 9000
- Toshiba Satellite Pro 4600
- Sony Vaio R505
- Sony Vaio SRX-77P
- Gateway Solo 5350
- Gateway Solo 9550
- HP Omnibook 6100
- HP NC4000
- Fujitsu Lifebook B-Series
- Fujitsu Lifebook P-Series
Access Points:
- Adaptec AWN-8060 (b only) Access Point
- Atheros 5001X AP - 802.11a
- 3Com AirConnect AP
- Apple Airport Extreme Access Point
- Belkin AP F5D7130
- Broadcom 11b Wireless Router Reference Design - Linux
- Broadcom 11b Wireless Router Reference Design - VxWorks
- Broadcom 54g Wireless Router Reference Design - Linux
- Broadcom 54g Wireless Router Reference Design - VxWorks
- Broadcom 54a Wireless Router Reference Design - Linux
- Broadcom 54a Wireless Router Reference Design - VxWorks
- Buffalo Airstation WR-B11
- Cisco 340
- Cisco 350
- Cisco 1100 AP (IOS)
- Cisco 1220A AP (Vx)
- Cisco 1200B AP (Vx)
- Cisco 1200(a/b/g) Access Point(IOS)
- Dell TrueMobile 1170 AP
- D-Link AP614+ AP
- D-Link DL-713P Wireless Router
- D-Link DWL900 Wireless AP
- D-Link DWL900+ Wireless AP
- D-LINK DWL5000 AP
- D-Link DWL6000 Dualband Wireless AP
- D-LINK AirPlus Xtreme-G DI-624 (HW B1, FW 1.10) - Atheros
- D-Link DI 774 (a/b/g) Access Point
- D-Link DI 624 (b/g) Access Point
- Instant802.Gateway 7001 (a/b/g) Access Point
- Intel Pro/Wireless 5000 Dualband AP
- Intel ProWL 2011B Enterprise AP
- Intel Residential Wireless Router
- Intermec Mobile Lan 2106 - 802.11a
- Linksys BEFW11S4 Wireless Router
- Linksys WAP11 Wireless AP (Gold and 2.2)
- Linksys WET11 Wireless Ethernet Bridge
- Linksys BEFW11P1 AP
- Linksys BEFSX41 AP
- Linksys WAP51AB AP
- Linksys WRT54G Res Gateway AP
- Lucent AP-1000
- Lucent AP-2000
- Netgear Wireless Router MR814V2
- Netgear FWAG114 Dualband(a/b/g) Access Point
- Proxim Skyline Wireless Router
- Proxim AP2000 802.11a AP
- Proxim AP-600
- Microsoft Wireless Base Station MN-500
- Microsoft MN700 (b/g)Access Point
- SMC 7004AWBR Wireless Router
- Symbol Spectrum 24 Hi-Rate AP
- Symbol 4131 AP
Wireless Stations:
- ActionTec Wireless Mini-PCI
- Intel Pro/Wireless 2011
- Intel Pro/Wireless 2011B
- Intel Pro 5000 802.11a Cardbus Card
- Cisco 350 802.11b wireless PCMCIA
- Cisco 340 802.11b wireless PCMCIA
- Cisco 802.11a Air-CB20A
- Lucent ORiNOCO 802.11b wireless PCMCIA
- Lucent (Agere) 802.11b wireless Mini-PCI
- 3Com AirConnect STA
- Symbol Spectrum 4121 Hi-Rate STA
- Linksys WPC11 2.0 (Prism 2.0)
- Linksys WPC11 2.5 (Prism 2.5)
- Linksys WPC11 3.0 (Prism 3.0)
- Linksys WPC11 3.1 (Prism 3.1)
- Linksys WUSB11v2.6
- Linksys WPC51AB Dual-Band Wireless A+B PC Card Adapter
- Linksys PCI card 4301
- Linksys Instant Wireless PCI Card
- IBM 802.11b wireless Mini-PCI (Intersil 2.5)
- SMC 802.11b wireless PCMCIA
- Netgear 802.11b wireless PCMCIA
- D-Link 802.11b wireless PCMCIA
- D-Link DWL-650+ Cardbus HW A1 FW 1.0 - Intersil
- D-Link DWL-650+ Cardbus HW B1 FW 2.0 - Atheros
- Cirrus Logic 802.11b Wireless PCMCIA
- Atheros 802.11a 5000 Cardbus Card
- Atheros 802.11a 1001X Cardbus Card
- Belkin Wireless Desktop PCI Network Card F5D6001
- Belkin Wireless Notebook Network Card F5D6020
- Microsoft Wireless USB Adapter MN-510
- Microsoft Wireless Notebook Adapter MN-520
Servers:
- Cisco Secure Access Control Server (ACS) v3.3 (Supports EAP-FAST)
- Cisco Secure Access Control Server (ACS) V3.2
- Cisco Secure Access Control Server (ACS) V3.1
- Cisco Secure Access Control Server (ACS) V2.6
- Microsoft Radius Server (IAS) Windows 2000
- Microsoft Radius Server (IAS) Windows 2003
- Funk Odyssey Radius Server
- Secure Computing Safe Word Premier Access Token Server
- Meetinghouse Aegis Server v1.1.4
- Microsoft Windows 2003 Certificate Authority

Known Limitations, Problems, and Notices

To satisfy HCT 12 WHQL, the default for our IBSS link behavior is changed. Now the driver only indicates "link up" on an IBSS if there is at least one other IBSS member. The corresponding TrayApp versions are intended to account for the change, as do Windows/XP SP1 and SP2. NOTE: EARLIER VERSIONS OF THE UI, AND XP "GOLD" WILL WORK DIFFERENTLY with the new driver. There will be a few beacons from the created IBSS, but after a few seconds w/o a link up indication the management application will teardown the IBSS and move to the next preferred network in the list (PN). The IBSS won't be tried again until the next cycle through the PN list.
GINA validated wireless networks that use certificates must use the machine store and not a user store as the user has not logged in yet
With certificate based networks, it is an invalid configuration to have a certificate chain that crosses user and machine cert store boundaries
When a user exports a series of preferred networks, and an EAP type is selected that requires a certificate, it is not possible to export where in the machine to get the certificate, as each machine stores certificates in a unique location (it is a hash function).
When running Afterburner enabled subsystems, the TCP/IP setting within Windows must be enlarged to gain the full effects of the throughput opportunity.
The control panel and tray application now support WPA and CCX in an integrated fashion. This is left on when running in WindowsME or Windows SE for evaluation purposes only. The implementation is not production worthy for 9x.
For 802.11a + WPA WIFI testing, a Synad AP is required. This access point is not obtainable, nor has it been for nearly a year. Thus we run our internal tests with a different access point. No issue has ever come about due to the Synad AP in the past.
This release supports customizable help files. If you want to modify the English help file shipped with the release you can edit the HTML files (convert the .chm file with the Microsoft help compiler - hhc.exe) and then compile a new chm file. At that point, simply drop bcmwlhlp.chm into the release directory on top of the one that we shipped to you and it will be installed automatically along with the rest of the driver files. If you wish to remove the help file from the release, simply delete the .chm file and InstallShield will automatically sense that.
Customer shall (i) obtain all government approvals and registrations for Customer's use of the software and (ii) comply with all applicable laws, rules, and regulations in connection therewith (including, without limitation, regulatory requirements under Title 47 CFR Part 15, Industry Canada RSS-210, European Directive 1999/5/EC, and regulations related to RF exposure). Customer understands and acknowledges that the software is subject to all pertinent import and export laws of the United States.
This product includes software developed by MDC and its licensors. This product includes software developed by the OpenSSL Project for use in the OpenSSL Toolkit (http://www.openssl.org/). This product includes cryptographic software written by Eric Young (eay@cryptsoft.com). This product includes software written by Tim Hudson (tjh@cryptsoft.com).
Integrated supplicants (we manage the network) have not been tested when configured as TTLS:MD5 as well as TTLS:CHAP. We are unable to locate backend servers that support this at release time.
In previous releases, for OEM evaluation, it was possible to set the locale to "ALL". If the driver is configured for "ALL" on a dualband system, and WZC is managing the network, you must use a preferred network configuration to execute the same evaluation.
To enable Soft-AP as a feature, you must modify your .inf file. Simply add the following text to your .inf file within [common.reg]:
HKR, ,"EnableSoftAP", 0, "1".
- Soft-AP is only available for Windows XP
- When Soft-AP function is enabled, the Wireless Networks, Link Status, Site Monitor and Diagnostics will all be disabled.
- Users must turn-off Windows XP "Zero configuration" (WZC) and therefore scanning.
Once Soft-AP is up and running a new control panel tab will appear.
- To make the feature useful, you will want to bridge the wireless driver with an Ethernet driver under Windows XP so that all wireless packets make their way to an Ethernet network where there is presumably access to the Internet. Look in Network Connections, right click the wireless device and select Bridge Connections.
- Check "Enable AP" in the "AP Config" tab, and uncheck the "Use Windows to Configure My Wireless Network Settings" in the "Wireless Networks" tab.
- Configure your new *SoftAP* via this window and you are set to go.
- To disable Soft-AP, uncheck the “Enable AP” checkbox and also re-enable Windows Zero Configuration to bring the device to the normal client mode.
The Soft-AP feature does NOT support Wi-Fi Protected Access (WPA). It does support WEP.
When disabling the Soft-AP feature, and you are running Microsoft WPA supplicants (Windows XP), you will need to wait for ~30 seconds after disabling SoftAP for the system to be configurable again.
CCX support cannot run properly in a multi-adapter configuration
In Chinese and Japanese versions of Windows, installing an unsigned driver will result in bcmwl5.sys to not getting updated. This is not an issue as long as the driver is signed.
Broadcom Reference software includes a loose binding in the .inf file. It will bind to any adapter with the Broadcom vendor and device id. If you do not remove it, or further qualify it with a sub-vendor and sub-device ID, that driver will load on any vendor's hardware.
Users should be made aware of how to properly use InstallShield. For optimal ease of installation
- Run the InstallShield executable setup.exe
- After InstallShield finishes, shut down the system
- Install the 802.11 network interface card
- Turn on system
- Prior to getting WHQL approved .cat files you will want to be aware of the following steps during system bootup:
- For WinXP:
  - Make use of all defaults in the New Hardware Wizard (select next and yes).
- For Win2K:
  - Select next twice
  - Ensure that all check boxes are unchecked
  - Select next twice
  - At the digital signature warning screen hit next
  - Select finish
To cleanly uninstall, users should be made aware of the application layer uninstall as opposed to uninstalling a device in the driver configuration tab (Properties:Configure:Driver:Uninstall). Users should follow the InstallShield uninstall procedure:
- Click on Start Menu
- Select the Control Panel
- Select Add or Remove Programs
- Select BRCM 802.11 Wireless Card (or your proper device string from the .inf file)
- Select Change/Remove
- Select OK
When installing in a system that has never run the driver before, simply use the normal driver installation once the hardware is detected.
There are some special instructions to be followed to obtain passing WHQL results:
- When running WHQL tests, be sure to remove the Tray Applet.
- As per MSFT WHQL guidelines, warnings will not prevent attaining a logo.

What's New in the 3.100.41.0 Release?

Imported New MeetingHouse Supplicant to fix::
- an intermittent deadlock coming out of suspend on Win2K
- Fixed a memory leak in the supplicant
Fixed machine-certificate/SSO network could not re-authenticate if the connection lost while logged into Windows
Resolved an issue where SSO initiates after unlocking workstation with active connection
Resolved a quick connect UI issue. An unknown key populated WEP networks when trying to configure it
Key provided automatically on WEP network added via Quick Connect
Fixed several translation issues
- Junk Character found in install shield
- Start menu shortcut was redundantly describing "Utility"
- Localized Version Info Tab had a cut off sentence
- "Refresh" button is slightly truncated on Available Network page

WIFI WPA + 802.11g Test Results

SECTION 5.0: AP TEST CONFIGURATIONS - WPA+802.11g


5.1.1 OOB Verification	Pass
5.1.2 Configurability Test
- Turn WPA on or off	Pass
- When WPA is on, verify PSK or TLS can be selected	Pass
- Multicast/unicast keys & mixture of WPA/WPA cannot be selected	Pass
- Spefigy SSID string	Pass
- Specify default pass phrase ("12345678") forWPA-PSK can be configured	Pass
5.1.3 WPA Initial Ping Test
- APs: Security: WPA-TLS, Ch: 11, Server: Funk
- STAUT: on Win2K using Funk supplicant
- Atheros AP	Pass
- Broadcom AP	Pass
- Globespan AP	Pass
- Proxim AP	Pass
- TI AP	Pass
5.2.2.1 - Configuration #S1-Pure G --- Broadcom-G AP
- (ESSID: a, WEP: off, Ch: 1, B-Rates: 1, 2, 5.5, 11, Beacons: 50, RTS: off, Frag: off): STA on Win2K
- Data Transfer 1: FileSendLong Tx - S1GDT1 [13.02]	Pass
- Data Transfer 2: FileSendLong Rx - S1GDT2 [13.32]	Pass
- Data Transfer 3: InquiryLong Tx - S1GDT3 [1.05]	Pass
- Data Transfer 2(NAV): if throughput less than 80% of throughput measured in DT#2	Pass
- Data Transfer 2(PLCP): if throughput less than 80% of throughput measured in DT#2	Pass
5.2.2.2 - Configuration #S1-Pure B --- Cisco-B AP
- (ESSID: a, WEP: off, CH: 2, B-Rates: 1, 2, 5.5, 11, Beacons: 50, RTS: off, Frag: off): STA on Win2K
- Data Transfer 1: FileSendLong Tx - S1BDT1 [3.64]	Pass
- Data Transfer 2: FileSendLong Rx - S1BDT2 [3.63]	Pass
- Data Transfer 3: InquiryLong Tx - S1BDT3 [0.66]	Pass
5.2.2.3 - Configuration #S1-Mix BG --- Glopespan-G AP
- (ESSID: a, WEP: off, CH: 3, B-Rates: 1, 2, 5.5, 11, Beacons: 50, RTS: off, Frag: off): STA on Win2K
- STA B Values: Atheros-G in 802.11b only mode, RTS: 256, Frag: 500
- Data Transfer 1: FileSendLong Tx - S1MGDT1 [3.93]	Pass
- S1MBDT1 [1.50]	Pass
- Data Transfer 2: FileSendLong Rx - S1MGDT2 [5.36]	Pass
- S1MBDT2 [0.30]	Pass
- Data Transfer 3: InquiryLong Tx - S1MGDT3 [0.61]	Pass
- S1MBDT3 [0.07]	Pass
5.2.2.4 - Configuration #S2-Pure G --- Globespan-G AP
- (ESSID: abcdefghijklmnopqrstuvwxyzABCDEF, WEP: PSK_12345678, Supplicant: MS, CH: 4,
B-Rates: 1, 2, 5.5, 11, Beacons: 100, RTS: off, Frag: 500): STA on WinXP
- Data Transfer 1: FileSendLong Tx - S2GDT1 [8.12]	Pass
- Data Transfer 2: FileSendLong Rx - S2GDT2 [7.10]	Pass
- Data Transfer 3: InquiryLong Tx - S2GDT3 [0.70]	Pass
5.2.2.5 - Configuration #S2-Pure B --- Cisco-B AP
- (ESSID: 12345678901234567890123456789012, WEP: PSK_12345678, Supplicant: MS, CH: 5,
B-Rates: 1, 2, 5.5, 11, Beacons: 100, RTS: 256, Frag: off): STA on WinXP
- Data Transfer 1: FileSendLong Tx - S2BDT1 [3.25]	Pass
- Data Transfer 2: FileSendLong Rx - S2BDT2 [3.30]	Pass
- Data Transfer 3: InquiryLong Tx - S2BDT3 [0.50]	Pass
5.2.2.6 - Configuration #S2-Mix BG --- Broadcom-G AP
- (ESSID: abcdefghijklmnopqrstuvwxyzABCDEF, WEP: PSK_12345678, Supplicant: MS, CH: 6,
B-Rates: 1, 2, 5.5, 11, Beacons: 100, RTS: off, Frag: off)
- STA B Values: Globespan-B, RTS: off, Frag: 500 (STA on WinXP)
- Data Transfer 1: FileSendLong Tx - S2MGDT1 [3.00]	Pass
- S2MBDT1 [2.60]	Pass
- Data Transfer 2: FileSendLong Rx - S2MGDT2 [2.30]	Pass
- S2MBDT2 [0.36]	Pass
- Data Transfer 3: InquiryLong Tx - S2MGDT3 [0.42]	Pass
- S2MBDT3 [0.43]	Pass
5.2.2.7 - Configuration #S3-Pure G --- TI-G AP
- (ESSID: space here, WEP: 0x9876543210, CH: 7, B-Rates: 1, 2, 5.5, 11, 6, 12, 24,
Beacons: 200, RTS: off, Frag: off): STA on Win2K
- Data Transfer 1: FileSendLong Tx - S3GDT1 [13.42]	Pass
- Data Transfer 2: FileSendLong Rx - S3GDT2 [12.62]	Pass
- Data Transfer 3: InquiryLong Tx - S3GDT3 [0.88]	Pass
5.2.2.8 - Configuration #S3-Pure B --- Cisco-B AP
- (ESSID: space here, WEP: 0x9876543210, CH: 8, B-Rates: 1, 2, 5.5, 11, Beacons: 200,
RTS: off, Frag: 500): STA on Win2K
- Data Transfer 1: FileSendLong Tx - S3BDT1 [2.25]	Pass
- Data Transfer 2: FileSendLong Rx - S3BDT2 [3.63]	Pass
- Data Transfer 3: InquiryLong Tx - S3BDT3 [0.64]	Pass
5.2.2.9 - Configuration #S3-Mix BG --- TI-G AP
- (ESSID: space here, WEP: 0x9876543210, CH: 9, B-Rates: 1, 2, 5.5, 11, Beacons: 200,
RTS: off, Frag: off)
- STA B Values: Globespan-B, RTS: 256, Frag: off (STA on Win2K)
- Data Transfer 1: FileSendLong Tx - S3MGDT1 [3.70]	Pass
- S3MBDT1 [2.45]	Pass
- Data Transfer 2: FileSendLong Rx - S3MGDT2 [2.54]	Pass
- S3MBDT2 [0.40]	Pass
- Data Transfer 3: InquiryLong Tx - S3MGDT3 [0.50]	Pass
- S3MBDT3 [0.39]	Pass
5.2.2.10 - Configuration #S4-Pure G --- Proxim-G AP
- (ESSID: a, WEP: WPA-TLS, Supplicant/Server: MS/MS CH: 10, B-Rates: 1, 2, 5.5, 11, 6, 12, 24,
Beacons: 500, RTS: 256, Frag: 500): STA on WinXP
- Data Transfer 1: FileSendLong Tx - S4GDT1 [8.27]	Pass
- Data Transfer 2: FileSendLong Rx - S4GDT2 [12.0]	Pass
- Data Transfer 3: InquiryLong Tx - S4GDT3 [1.05]	Pass
5.2.2.11 - Configuration #S4-Pure B --- Cisco-B AP
- (ESSID: a, WEP: WPA-TLS, Supplicant/Server: MS/MS, CH: 11, B-Rates: 1, 2, 5.5, 11, Beacons: 500,
RTS: 256, Frag: 500): STA on WinXP
- Data Transfer 1: FileSendLong Tx - S4BDT1 [2.50]	Pass
- Data Transfer 2: FileSendLong Rx - S4BDT2 [2.19]	Pass
- Data Transfer 3: InquiryLong Tx - S4BDT3 [0.50]	Pass
5.2.2.12 - Configuration #S4-Mix BG --- Proxim-G AP
- (ESSID: a, WEP: WPA-TLS, Supplicant/Server: MS/MS, CH: 11, B-Rates: 1, 2, 5.5, 11, Beacons: 500,
RTS: Off, Frag: off): STA on WinXP
- STA B Values: Intel-B, RTS: off, Frag: off
- Data Transfer 1: FileSendLong Tx - S4MGDT1 [2.80]	Pass
- S4MBDT1 [1.80]	Pass
- Data Transfer 2: FileSendLong Rx - S4MGDT2 [2.80]	Pass
- S4MBDT2 [2.06]	Pass
- Data Transfer 3: InquiryLong Tx - S4MGDT3 [0.40]	Pass
- S4MBDT3 [0.25]	Pass
5.3.1 - WPA Same Mode Roaming with an Authentication Server
- (ESSID: roaming, WEP: WPA-TLS, Supplicant/Server: Funk/Funk, Ch:8, Frag/RTS: Off): STA on Win2K
- Globespan-G(AP2)	Pass
- TI-G(AP3)	Pass
- Proxim-G(AP4)	Pass
5.3.2 - WPA Same Mode Roaming using Pre-Shared Keys
- (ESSID: roaming, WEP: PSK_12345678, Supplicant: Funk, Ch:9, Frag/RTS: Off): STA on Win2K
- Globespan-G(AP2)	Pass
- TI-G(AP3)	Pass
- Proxim-G(AP4)	Pass
5.4.1 - Configuration #MCS1 --- Broadcom-G AP Values: (ESSID: Multicast, WEP: 0x0123456789,
CH: 8, B-Rates: 1, 2, 5.5, 11, Beacons: 100, RTS: off, Frag: off)
- STAUT(G-STA-MC-1)on Win2K: All Default --- Atheros-G STA(G-STA-MC-2): All Default
- Data Transfer: Realaud Rx	Pass
5.4.2 - Configuration #MCS2 --- Proxim-G AP Values: (ESSID: Multicast, WEP: PSK_0123456789,
Supplicant: MS, CH: 11, B-Rates: 1, 2, 5.5, 11, 6, 12, 24, Beacons: 150, RTS&Frag: off)
- STAUT(G-STA-MC-1) on Win2XP: All Default --- TI-G STA(G-STA-MC-2): Power Save: PSPOLL
- Data Transfer: Realaud Rx	Pass
5.5 Negative Tests
- Wrong ESSID:	Pass
- Wrong Case in ESSID:	Pass
- ESSID Substring:	Pass
- WEP key mismatch:	Pass
- Station/AP WEP mismatch:	Pass
5.6.1 STA Countermeasures
- After the first bad frame STA continues to ping	Pass
- After the second bad frame STA continues to ping	Pass
- After the third bad frame STA deauthenticates and pings stop	Pass
- After 60 seconds the STA can associate and the ping session resumes	Pass
5.6.2.1 STA WPA Negative Tests: Non-Association with a WEP AP(Proxim)
- ESSID: wpa, WEP: 9876543210, Ch: 11, B-Rate: 1, 2, 5.5, 11, Beacons: 100; Frag/RTS: Off
- STAUT on WinXP: Configure for WPA-TLS
- Verify the STA does not receive a ping response from the authenticaton server	Pass
5.6.2.1 STA WPA Negative Tests: Non-Association with an AP not using WPA(Proxim)
- ESSID: wpa, WEP: Off, Ch: 11, B-Rate: 1, 2, 5.5, 11, Beacons: 100; Frag/RTS: Off
- STAUT on WinXP: Configure for WPA-TLS
- Verify the STA does not receive a ping response from the authenticaton server	Pass
5.6.2.3.1 STA WPA Negative Tests: Non-Association with a PSK configured station(Broadcom)
- ESSID: wpa, WEP: WPA-TLS, Server: MS, Ch: 11, B-Rate: 1, 2, 5.5, 11, Beacons: 100; Frag/RTS: Off
- STAUT on WinXP: configured for WPA-PSK: 12345678
- Verify an Atheros STA configured for WPA-TLS can associate and can ping the server	Pass
- Verify the STA does not receive a ping response from the authenticaton server	Pass
5.6.2.3.2 STA WPA Negative Tests: Non-Association with a TLS configured station(Broadcom)
- ESSID: wpa, WEP: PSK_12345678, Ch: 11, B-Rate: 1, 2, 5.5, 11, Beacons: 100; Frag/RTS: Off
- STAUT on WinXP: configured for WPA-TLS
- Verify an Atheros STA configured for WPA-PSK can associate and can ping the server	Pass
- Verify the STA does not receive a ping response from the authenticaton server	Pass
SECTION 6.0: IBSS TEST CONFIGURATIONS WPA+802.11g
SECTION 6.0: IBSS TEST CONFIGURATIONS WPA+802.11g
6.1.1 - Active Scan Tests
Creator STA = Station Under Test (ESSID: active scan, WEP: off, CH: 1, all else default)	Pass
Join STA = Atheros-G---> (Frag: 384); (RTS: Off)	Pass
Verify SUT responds with a valid response to probe	Pass
Verify basic rates enumerated in the beacons are only 1, 2, 5.5 and 11 Mbps	Pass
Verify the channel in beacon frame is correct	Pass
Verify EID=42 and EID=50 are NOT present in the beacon message	Pass
Verify BSSID is a random value after restart	Pass
Data Transfer #1: FileSendLong from Atheros-G to SUT - SI1DT1 [1.8]	Pass
Data Transfer #2: FileSendLong from SUT to Atheros-G - SI1DT2 [3.5]	Pass
6.2.1 - Passive Scan Tests
Creator STA = Station Under Test (ESSID: passive scan, WEP: 0x1122334455, CH: 11, Frag: off, RTS: off)	Pass
Join STA = Atheros-G---> (Frag: off, RTS: 300)	Pass
Verify SUT responds with a valid response to probe	Pass
Verify basic rates enumerated in the beacons are only 1, 2, 5.5 and 11 Mbps	Pass
Verify the channel in beacon frame is correct	Pass
Verify EID=42 and EID=50 are NOT present in the beacon message	Pass
Verify BSSID is a random value after restart	Pass
Data Transfer #1: FileSendLong from Atheros-G to SUT - SI2DT1 [1.7]	Pass
Data Transfer #2: FileSendLong from SUT to Atheros-G - SI2DT2 [3.4]	Pass
6.3.1 - IBSS WEP on Tests
Creator STA = Globespan-G (ESSID: IBSS wep on, WEP: 0xdeadbeef12, CH: 4, B-Rates: 1, 2, 5.5, 11,	Pass
S-Rates: 1, 2, 5.5, 11, Frag: off, RTS: Off)	Pass
Joiner STA1 = Buffalol-G---> (Frag: off, RTS: 300)	Pass
Joiner STA2 = STA Under Test ---> (All default)	Pass
Verify SUT responds with a valid response to probe	Pass
Verify basic rates enumerated in the beacons are only 1, 2, 5.5 and 11 Mbps	Pass
Verify the channel in beacon frame is correct	Pass
Verify EID=42 and EID=50 are NOT present in the beacon message	Pass
User sniffer to capture a trace for 2 minutes and verify beacons fairly distributed between stations	Pass
Data Transfer #1: FileSendLong from Buffalo-G to SUT - SI3DT1 [3.2]	Pass
Data Transfer #2: FileSendLong from SUT to Buffalo - SI3DT2 [3.5]	Pass
Data Transfer #3: Multicast Realaud - SI3DT3 [0.06] - Broadcaster: Globespan, Receiver: SUT	Pass
Data Transfer #4: Multicast Realaud - SI3DT4 [0.06] - Broadcaster: SUT, Receivers: Buffalo-G and Globespan-G	Pass
6.4.1 - IBSS WEP off Tests
Creator STA = Atheros-G (ESSID: IBSS wep off, WEP: off, CH: 8, B&S Rates: Default, Frag&RTS: off)	Pass
Joiner STA1 = Buffalo-G---> (Frag: 400, RTS: 300)	Pass
Joiner STA2 = STA Under Test ---> (All default)	Pass
Verify SUT responds with a valid response to probe	Pass
Verify basic rates enumerated in the beacons are only 1, 2, 5.5 and 11 Mbps	Pass
Verify the channel in beacon frame is correct	Pass
Verify EID=42 and EID=50 are NOT present in the beacon message	Pass
User sniffer to capture a trace for 2 minutes and verify beacons fairly distributed between stations	Pass
Data Transfer #1: FileSendLong from Atheros-G to SUT - SI4DT1 [3.5]	Pass
Data Transfer #2: FileSendLong from SUT to Atheros-G - SI4DT2 [3.5]	Pass
Data Transfer #3: FileSendLong from Buffalo-G to SUT - SI4DT3 [1.9]	Pass
Data Transfer #4: FileSendLong from SUT to Buffalo-G - SI4DT4 [3.5]	Pass
6.5.1 Re-Join Tests
Creator STA = Globespan-G (ESSID: coalesce, WEP: off, CH: 11, B&S Rates: Default, Frag: off, RTS: off)	Pass
Joiner STA1 = TI-G---> (Frag: off, RTS: off, all else default)	Pass
Joiner STA2 = STA Under Test ---> (CH: 11, Frag: off, RTS: off, all else default)	Pass
Move SUT out of range and verify not receiving beacons	Pass
Move SUT back into range, verify connection to 3 STAs	Pass

WIFI WPA + 802.11b Test Results

WIFI WPA AP Test Configurations
4.1 Out of the box Verification	Pass
4.3 Configuration Paramters
- Turn WPA on or off	Pass
- When WPA is on, Verify PSK of TLS can be selected	Pass
- Multicast/unicast keys & mixture of WPA/WEP cannot be selected	Pass
- Specify SSID string	Pass
- Specify default pass phrase ("12345678") for PSK WPA	Pass
5.0 Initial Ping Test - Win2K & Funk 802.1x Supplicant in EAP-TLS
- Atheros AR5BAP - 00025A (AP1)	Pass
- Cisco AIR-AP1230B (AP2)	Pass
- Broadcom AP BCM4306 (AP3)	Pass
- Intersil PRISM ISL36356A (AP4)	Pass
6.1 Same Mode Roaming with Authentication Server - Win2k & Funk
- Cisco AIR-AP1230B (AP2)	Pass
- Broadcom AP BCM4306 (AP3)	Pass
- Intersil PRISM ISL36356A (AP4)	Pass
6.2 Same Mode Roaming Using Pre-Shared Keys - Win2K & Funk
- Cisco AIR-AP1230B (AP2)	Pass
- Broadcom AP BCM4306 (AP3)	Pass
- Intersil PRISM ISL36356A (AP4)	Pass
7.2 STA Countermeasures - Win2K
1. The Access Point generates a single bad frame	Pass
- Verify the STA continues to ping for the next 70 seconds	Pass
2. The access Point generates a second bad frame	Pass
- Verify the STA continues to ping for the next 50 seconds	Pass
3. The Access Point generates a third bad frame	Pass
- Verify the STA deauthenticate the pings stops	Pass
4. Verify the STA could only reassociate after 60 seconds	Pass
9.1.1 STA Point-to-point Throughput - XP
a. WPA - EAP-TLS	Pass
- S1DT1 [4.0Mbps] - Cisco 1230B	Pass
- S1DT2 [3.5Mbps] - Cisco 1230B	Pass
- S1DT3 [0.2Mbps] - Cisco 1230B	Pass
- S2DT1 [1.5Mbps] - Broadcom AP BCM4306	Pass
- S2DT2 [3.5Mbps] - Broadcom AP BCM4306	Pass
- S2DT3 [0.3Mbps] - Broadcom AP BCM4306	Pass
b. WPA-PSK	Pass
- S1DT1 [4.0Mbps] - Cisco 1230B	Pass
- S1DT2 [3.5Mbps] - Cisco 1230B	Pass
- S1DT3 [0.2Mbps] - Cisco 1230B	Pass
- S2DT1 [1.5Mbps] - Broadcom AP BCM4306	Pass
- S2DT2 [3.5Mbps] - Broadcom AP BCM4306	Pass
- S2DT3 [0.3Mbps] - Broadcom AP BCM4306	Pass
9.1.2 STA Multicast Throughput - Using Cisco 1230B - XP
a. WPA - EAP-TLS	Pass
- SUT sends multicast data stream to STA2(Intersil)	Pass
- STA2 sends mulitcast data stream to SUT	Pass
b. WPA-PSK	Pass
- SUT sends multicast data stream to STA2(Intersil)	Pass
- STA2 sends mulitcast data stream to SUT	Pass
10.1 Non-Association with a WEP AP - XP
- Verify the STA does not complete the association with the AP	Pass
10.2 Non-Association with an AP not using WPA - XP
- Verify the STA does not complete the association with the AP	Pass
10.5.1 Non-Association with PSK configured station - XP
- Verify the STA does not complete the association with the AP	Pass
10.5.2 Non-Association with a TLS configured station
- Verify the STA does not complete the association with the AP	Pass

CCX Test Results

Cisco Client eXtensions v3.0 Test Plan Rev 3.5.4
8.1 EAP-FAST Functionality [S41]	Windows XP	Windows 2K
8.1.1 EAP-FAST authentication	Pass	Pass
8.1.2 EAP-FAST authentication with CMIC	Pass	Pass
8.1.3 EAP-FAST authentication with CKIP+CMIC	Pass	Pass
8.1.4 EAP-FAST authentication with session timeout	Pass	Pass
8.1.5 EAP-FAST authentication with broadcast key rotation	Pass	Pass
8.1.6 WPA with EAP-FAST authentication	Pass	Pass
8.1.7 WPA with EAP-FAST authentication with session timeout	Pass	Pass
8.1.8 WPA with EAP-FAST authentication with broadcast key rotation	Pass	Pass
8.1.9 WPA optional with EAP-FAST authentication and TKIP+WEP128	Pass	Pass
8.1.10 EAP-FAST clients on different VLANs are able to pass data to each other	Pass	Pass
8.1.11 EAP-FAST authentication failure - authentication timeout	Pass	Pass
8.1.12 EAP-FAST authentication failure - incorrect username	Pass	Pass
8.1.13 EAP-FAST authentication failure - incorrect password	Pass	Pass
8.2 CCKM with EAP-FAST [S45]
8.2.1 CCKM with EAP-FAST authentication and WEP 128 cipher	Pass	Pass
8.2.2 CCKM with EAP-FAST authentication with CMIC	Pass	Pass
8.2.3 CCKM with EAP-FAST authentication with CKIP+CMIC	Pass	Pass
8.2.4 CCKM with EAP-FAST authentication with TKIP	Pass	Pass
8.2.5 CCKM with EAP-FAST authentication with session timeout set by AP	Pass	Pass
8.2.6 CCKM with EAP-FAST authentication with broadcast key rotation	Pass	Pass
8.3 WMM Basic Functionality [S44] - Run for each PHY
8.3.1 WMM prioritization with Open authentication	Pass	Pass
8.3.2 WMM prioritization with LEAP authentication with WEP128 cipher	Pass	Pass
8.3.3 WMM prioritization with CCKM key management with LEAP authentication with CKIP+CMIC cipher	Pass	Pass
8.3.4 WMM prioritization with WPA key management with LEAP authentication with TKIP cipher	Pass	Pass
8.3.5 WMM prioritization with EAP-FAST authentication with WEP128 cipher	Pass	Pass
8.3.6 WMM prioritization with CCKM key management with EAP-FAST authentication with CKIP+CMIC cipher	Pass	Pass
8.3.7 WMM prioritization with WPA key management with EAP-FAST authentication with TKIP cipher	Pass	Pass
8.3.8 WMM prioritization with PEAP-GTC authentication	Pass	Pass
8.4 Single Signon (Windows 2k/XP) - LEAP Setting and Dependency with CLM [S46]
8.4.1 Windows Username and Password	Pass	Pass
8.4.2 Use Saved LEAP Username Password	Pass	Pass
8.5 Single Signon (Windows 2k/XP) - Additional Support for various features [S46]
8.5.1 Standby/Hibernation Support	Pass	Pass
8.5.2 Plug and Play Support (removable client adapters only)	Pass	Pass
8.5.3 Multiple Domain Support	Pass	Pass
8.5.4 Password Change Support	Pass	Pass
8.5.5 Password Expiration Suport	Pass	Pass
8.6 Single Signon (Windows 2k/XP) - Responses and Error Messages (Negative Test Cases) [S46]
8.6.1 LEAP Authentication Status	Pass	Pass
8.6.2 Error Messages during LEAP Authentication	Pass	Pass
8.6.3 Verify CLM handles LEAP authentication timeout correctly	Pass	Pass
8.7 Single Signon (Windows 2k/XP) - Other Test Cases
8.7.1 Insertion of wireless adapter(Cardbus or PCMCIA only)	Pass	Pass
8.7.2 Removal of wireless adapter(Cardbus or PCMCIA only)	Pass	Pass
8.8 WPA2 [S48]
8.8.1 WPA2 with LEAP authentication with AES-CCM cipher	Pass	Pass
8.8.2 WPA2 with EAP-FAST authentication with AES-CCM cipher	Pass	Pass
8.8.3 WPA2 with PEAP-GTC authentication with AES-CCM cipher	Pass	Pass
8.9 WMM+WPA2 [S48] - Run for each PHY
8.9.1 WMM prioritization with WPA2 with LEAP authentication with AES-CCM cipher	Pass	Pass
8.9.2 WMM prioritization with WPA2 with EAP-FAST authentication with AES-CCM cipher	Pass	Pass
8.9.3 WMM prioritization with WPA2 with PEAP-GTC authentication with AES-CCM cipher	Pass	Pass

Cisco Client eXtensions v2.0 Test Plan Rev 3.10
6.3.0 AP Control of Client Transmit Power[S31]	Windows XP	Windows 2K
6.3.1 TPC IE from multiple Aps - Use of correct power setting upon a successful authentication	Pass	Pass
6.3.2 Client uses the minimum power limit set by the AP or configured power limit set by the client's host	Pass	Pass
6.3.3 Client uses the maximum power limit set by the AP or configured power limit set by the client's host	Pass	Pass
6.4.0 AP Assisted Roaming [S32] - Test on each PHY
6.4.1.1 Client send DDP information of previous AP(channel, SSID and amount of time since losing association)	Pass	Pass
6.4.1.2 Client does not send DDP information of the previous AP if it failed LEAP authentication to the new AP	Pass	Pass
6.4.1.3 Client roams to another AP in 125msecs or less when the radio channels are the same	Pass	Pass
6.4.1.4 Client roams to another AP in <=125 msecs when the radio channel is at opposite ends of frequency band	Pass	Pass
6.5.0 Fast Reauthentication with CCKM [S33] - Test on each PHY
6.5.1.1 Single CCKM AP Initial Authentication to SSID	Pass	Pass
6.5.2.1 CCKM MN Fast Authentication - Client Roaming	Pass	Pass
6.5.3.1 Single CCKM AP Session Timeout	Pass	Pass
6.6.0 PEAP Supplicant [S34]
6.6.1.1 PEAP Supplicant Installation/Configuration	Pass	Pass
6.6.1.2 One time password (Soft Token)	Pass	Pass
6.6.1.4 PEAP Re-Authentication - Roaming - Soft Token	Pass	Pass
6.7.0 WPA TKIP with LEAP and PEAP [S35]
6.7.1 Verify client can authenticate using Cisco LEAP and use the new WPA Standard TKIP	Pass	Pass
6.7.2 Verify client can authenticate using PEAP with EAP-GTC and use the new WPA Standard TKIP	Pass	Pass
6.8.0 Radio Measurement Requests [S36] - Test on each PHY
6.8.1.1 Beacon Report - Passive Scan, Same Channel	Pass	Pass
6.8.1.2 Beacon Report - Beacon Table Scan	Pass	Pass
6.8.1.3 Beacon Report - Passive Scan, Different Channel	Pass	Pass
6.8.1.4 Beacon Report - Active Scan, Different Channel	Pass	Pass
6.8.3.1 Channel Load Report - Same Channel	Pass	Pass
6.8.3.2 Channel Load Report - Different Channel	Pass	Pass
6.8.4.1 Noise Histogram Report - Same Channel	Pass	Pass
6.8.4.2 Noise Histogram Report - Different Channel	Pass	Pass
6.8.5.1 Multiple Radio Measurement Requests - With traffic on same channel	Pass	Pass
6.8.5.2 WLSE Testing: Multiple Radio Measurement Requests - With traffic on same channel	Pass	Pass
6.8.5.3 Multiple Radio Measurement Requests - With traffic on different channel	Pass	Pass
6.9.0 Cisco Compatible Extensions for WLAN Devices Version Number Reporting [S38]
6.9.1 Client communicates its Cisco Compatible Extensions for WLAN Devices version to the AP in a DDP packet	Pass	Pass
6.10.0 QoS Parameter Set Element [S39]
6.10.1 Client adopts Cwmin, Cwmax, AIFSN (fixed slot time) values sent by the Access Points	Pass	Pass

Cisco Client eXtensions v1.0 Test Plan Rev 3.08 Draft
4.1 802.11 Functionality	Windows XP	Windows 2K
4.1.1 Fragmentation support	Pass	Pass
4.1.2 CTS and RTS support	Pass	Pass
4.2 Use of SSID in Probe Request
4.2.1 Client ignore missing SSID in Beacons	Pass	Pass
4.2.2 Do not ROAM with multicast/broadcast decrypt error in VLAN environment	Pass	Pass
4.2.3 Client to use SSID in Probe Request	Pass	Pass
4.2.4 Multiple SSID support in Configuration Utility	Pass	Pass
4.3 Microsoft 802.11 NIC Compliance (WHQL) TBD seperately
4.4.1 802.1x Security Compliance/CKIP Support/40 and 128-bit WEP Keys/LEAP support
4.4.1.1 40-bit WEP (Open Authentication) with MIC/CKIP enabled	Pass	Pass
4.4.1.2 40-bit WEP (Open Authentication, with Different Transmit Keys) WEP Key 1&2	Pass	Pass
4.4.1.3 40-bit WEP (Shared-Key Authentication) with MIC an CKIP enabled	Pass	Pass
4.4.1.4 40-bit WEP (Shared-Key Authentication, with Different Transmit Keys) WEP Key 3&4	Pass	Pass
4.4.1.5 128-bit WEP (Open Authentication) with MIC and CKIP enabled	Pass	Pass
4.4.1.6 128-bit WEP (Open Authentication, Different Transmit Keys) WEP Key 1&2	Pass	Pass
4.4.1.7 128-bit WEP (Shared-Key Authentication) with MIC and CKIP enabled	Pass	Pass
4.4.1.8 128-bit WEP (Shared-Key Authentication, Different Transmit Keys) WEP Key 3&4	Pass	Pass
4.4.2 LEAP Functional Tests
4.4.2.1 LEAP (Using a 40-bit WEP Broadcast Key)	Pass	Pass
4.4.2.2 LEAP (Using a 128-bit WEP Broadcast Key)	Pass	Pass
4.4.4 EAP-TLS Functional Tests
4.4.4.1 EAP-TLS (Using a 40-bit Broadcast Key, Open Authentication) with MIC and CKIP enabled	Pass	XP Only
4.4.4.2 EAP-TLS (Using a 128-bit Broadcast Key, Open Authentication) with MIC and CKIP enabled	Pass	XP Only
4.4.5 Mixed Cell (WEP and Non-WEP) Functional Tests
4.4.5.1 40-bit WEP (Mixed-CELL Allowed)	Pass	Pass
4.4.5.3 128-bit WEP (Mixed-CELL Allowed)	Pass	Pass
4.4.5.5 LEAP 128-Bit WEP Key (Mixed Cell) - set encryption to Optional	Pass	Pass
4.4.6 Roaming with Security Features Enabled (128-Bit WEP key, MIC, CKIP, Broadcast-Key) EAP-TLS	Pass	XP Only
4.4.7 Performance Security Feature Enabled (128-Bit WEP key, MIC, CKIP) EAP-TLS	Pass	XP Only
4.4.7.1 Incrementing IV	Pass	Pass
4.5 Rogue AP Reporting Support	Pass	Pass
4.5.1 LEAP with invalid Authentication, Failure code 0x01 (Invalid authentication type)	Pass	Pass
4.5.2 Authentication Timeout, Failure code 0x02 (Authentication timeout)	Pass	Pass
4.5.3 Challenge from AP Failed, Failure code 0x03 (Challenge from AP failed)	Pass	Pass
4.6.2 Symbol IE	Pass	Pass
4.6.3 Device Identification in AP Association Table	Pass	Pass

WIFI 802.11a + WPA Test Results

*802.11a+WPA STA Interoperabilty Tests*
5.1 5 5 Station Testing - Infrastructure
5.1 Station OOB, Configurability and Initial Ping Tests
5.1.1 OOB Verification for a Station	PASS
5.1.2 Configurability Test for ESSID,WEP Key,default pass phrase (“12345678”) for PSK WPA	PASS
5.1.3 STA WPA Initial Ping Interoperability Test,Supplicant/Server Funk/Funk,STA O/S Windows 2000
- Broadcom AP	PASS
- Cisco AP	PASS
- Atheros AP	PASS
- Globespan AP	PASS
- Synad AP	PASS
5.2 Station/AP Association and Throughput Tests
5.2.1 Association,basic throughput tests	PASS
5.2.1.1 Association	PASS
5.2.1.2 Data Transfer 1(AP --> STA),Chariot script FILESENDL	PASS
5.2.1.3 Data Transfer 2 (STA --> AP),Chariot script FILESENDL	PASS
5.2.1.4 Data Transfer 3,Chariot script INQUIRYL	PASS
5.2.2 Configurations for Interoperability STA Testing
5.2.2.1 Configuration #S1
STA O/S Windows 2000
- Association	PASS
- Data Transfer 1(AP --> STA)(S1DT1 10.821)	PASS
- Data Transfer 2 (STA --> AP)(S1DT2 14.080)	PASS
- Data Transfer 3,Chariot script INQUIRYL(S1DT3 1.082)	PASS
- Honoring NAV Background(tput <80% of measured DT#1 with TI card sending CTS frames)	PASS
- Honoring PLCP Header Background(tput <80% of measured DT#1 with TI card sending PLCP frames)	PASS
5.2.2.2 Configuration #S2Broadcom,WPA-PSK,Win2000
- Association	PASS
- Data Transfer 1(AP --> STA) (S2DT1 7.000)	PASS
- Data Transfer 2 (STA --> AP)(S2DT2 12.552)	PASS
- Data Transfer 3,Chariot script INQUIRYL(S2DT3 1.000)	PASS
5.2.2.3 Configuration #S3,Cisco,WPA-PSK,Funk,Win2000
- Association	PASS
- Data Transfer 1(AP --> STA)(S3DT1 9.358)	PASS
- Data Transfer 2 (STA --> AP)(S3DT2 10.514)	PASS
- Data Transfer 3,Chariot script INQUIRYL(S3DT3 0.750)	PASS
5.2.2.4 Configuration #S4,Broadcom,WPA-TLS,Funk,Win2000
- Association	PASS
- Data Transfer 1(AP --> STA) (S4DT1 10.500)	PASS
- Data Transfer 2 (STA --> AP)(S4DT2 14.389)	PASS
- Data Transfer 3,Chariot script INQUIRYL(S4DT3 0.750)	PASS
5.2.2.5 Configuration #S5,Synad,WPA-TLS,Microsoft 2003 Server,Win XP
- Association	PASS
- Data Transfer 1(AP --> STA) (S5DT1 2.300)	PASS
- Data Transfer 2 (STA --> AP) (S5DT2 9.668)	PASS
- Data Transfer 3,Chariot script INQUIRYL (S5DT3 0.860)	PASS
5.2.2.6 Configuration #S6,Atheros,WEP, Win XP
- Association	PASS
- Data Transfer 1(AP --> STA) (S6DT1 13.451)	PASS
- Data Transfer 2 (STA --> AP) (S6DT2 14.951)	PASS
- Data Transfer 3,Chariot script INQUIRYL(S6DT3 1.264)	PASS
5.2.2.7 Configuration #S7,Cisco,WEP,Win XP
- Association	PASS
- Data Transfer 1(AP --> STA) (S7DT1 15.319)	PASS
- Data Transfer 2 (STA --> AP) (S7DT2 12.133)	PASS
- Data Transfer 3,Chariot script INQUIRYL (S7DT3 0.990)	PASS
5.2.2.8 Configuration #S6,Broadcom,Security off,Win XP
- Association	PASS
- Data Transfer 1(AP --> STA) (S8DT1 6.200)	PASS
- Data Transfer 2 (STA --> AP) (S8DT2 12.624)	PASS
- Data Transfer 3,Chariot script INQUIRYL (S8DT3 1.200)	PASS
5.3 STA Roaming
5.3.1 Same Mode Roaming with an Authentication Server
Atheros	PASS
Cisco	PASS
Synad	PASS
Broadcom	PASS
5.3.2 Same Mode Roaming using Pre-Shared key’s
ESSID roaming,Beacon Interval default,Channel 36,Security WPA-PSK = “12345678”,RTS/Fragmentation Off,
Supplicant Funk, STA O/S Windows 2000
Atheros	PASS
Cisco	PASS
Synad	PASS
Broadcom	PASS
5.4 Broadcast/Multicast reception
5.4.1 Multicast Configuration #MCS1
- Verify Realaud script completes without errors	PASS
5.4.2 Multicast Configuration #MCS2
- Verify Realaud script completes without errors	PASS
5.5 Negative Tests
5.5.1 Configuration mismatches
- Wrong ESSID:	PASS
- Wrong case in ESSID characters:	PASS
- Substring mismatch between STA and AP	PASS
- WEP key mismatch	PASS
5.6 STA WPA Specific Tests
5.6.1 STA Countermeausres with Win2K STA using Funk Supplicant against Synad AP
- After the first bad frame STA continues to ping for the next 70 seconds	PASS
- After the second bad frame STA continues to ping for the next 50 seconds	PASS
- After the third bad frame STA deauthenticates and pings stop	PASS
- After 60 seconds the STA can associate and the ping session resumes	PASS
5.6.2 STA WPA Negative Tests
5.6.2.1 Non-Association with a WEP AP
5.6.2.2 Non-Association with an AP not using WPA	PASS
5.6.2.3 Pre-Shared Key – 802.1X-TLS Rejection	PASS
5.6.2.3.1 Non-Association with PSK configured Station	PASS
5.6.2.3.2 Non-Association with a TLS configured station	PASS
6 Station Testing - IBSS
6.1 Active Scan Tests
6.1 Configuration SI1
- FILESNDL from Joiner to the SUT (SI1DT1 2.600)	PASS
- FILESNDL from SUT to Joiner (SI1DT2 13.598)	PASS
6.2 Passive Scan Tests
6.2 Configuration SI1
- FILESNDL from Joiner to the SUT (SI2DT1 11.481)	PASS
- FILESNDL from SUT to Joiner (SI2DT2 15.711)	PASS
6.3 IBSS WEP On Tests
- Chariot FILESNDLfrom Broadcom to the SUT (SI3DT1 14.055)	PASS
- Chariot multicast Real-Audio test with Intel as the broadcaster (SI3DT2 0.056)	PASS
- Chariot multicast Real-Audio test with SUT as the broadcaster (SI3DT3 0.056)	PASS
- Chariot FILESNDL from SUT to Broadcom (SI3DT4 15.327)	PASS
6.4 IBSS WEP Off Tests
- Chariot FILESNDL Intel to SUT (SI4DT1 15.468)	PASS
- Chariot FILESNDL SUT to Intel (SI4DT2 12.000)	PASS
- Chariot FILESNDL Broadcom to SUT (SI4DT3 9.009)	PASS
- Chariot FILESNDL SUT to Broadcom (SI4DT4 16.623)	PASS
6.5 Re-Join Tests
- Range tests within range,moved out of range,back in range.	PASS
7 Dual Band Tests
7.1 Bridging Throughput Test for Dual Band 802.11a and 802.11g APs
- Association	PASS
- Chariot FILESENDL, A-STA --> G-STA (DB1DT1 8.00)	PASS
- Chariot FILESENDL, G-STA --> A-STA (DB1DT2 10.00)	PASS
7.3 Cross-Band Station Roaming Test for Dual Band Stations
7.3.1 All APS are configured as: (ESSID: 0123456789012345678901234567890; Ch: 60 for 11a & 10 for 11g;
STA Roaming (TI-G -> Cisco-A ->Globespan G -> Atheros A- > TI-G)	Pass
7.3.2 All APS are configured as: (ESSID: 0123456789012345678901234567890; Ch: 60 for 11a & 10 for 11g;
STA Roaming (TI-G -> Cisco-A ->Globespan G -> Atheros A- > TI-G)	Pass
7.3.3 All APS are configured as: (ESSID: 0123456789012345678901234567890; Ch: 60 for 11a & 10 for 11g;
STA Roaming (TI-G -> Cisco-A ->Globespan G -> Atheros A- > TI-G)	Pass

WME/WMM 802.11 Test Results

WiFi 802.11 a/g + WMM STA Interoperability Test Matrix
5.1: WME-S1: Interworking with legacy Infrastructure: (1 legacy AP with WME STAUT)
STAUT: (WinXP, WEP Off, PS Off)
1. - Verify Beacon frame	Pass
2. - Verify If Probe Request contains any WME element. Fail if so.	Pass
3. - Verify If STAUT Association Request contains any WME element. Fail if so.	Pass
- Verify STAUT is associated. Pass if so.	Pass
4. - Record tx throughput of RTP1_BE and verify that thruput [9.7]	Pass
5. - Record rx throughput of RTP1_BE and verify that thruput [9.7]	Pass
5.2: WME-S2: Traffic differentiation in single BSS: (1 WME AP with 1 WME STAUT)
1. Verify Beacon frame	Pass
2. If a Probe Request occurs and STAUT Probe Request contains any WMM element, FAIL	Pass
3. If STAUT Association Request contains WMM information element AND STA Associated, PASS	Pass
4. STAUT Transmit RTP3_BE,Receive RTP1_BE,RTP2_VI
- Record tx throughput of RTP1_BE	Pass
- Record tx throughput of RTP2_VI	Pass
- Record rx throughput of RTP3_BE	Pass
5. STAUT Transmit RTP1_BE,RTP2_VI,RTP3_BE
- Record rx throughput of RTP1_BE	Pass
- Record rx throughput of RTP2_VI	Pass
- Record rx throughput of RTP3_BE	Pass
6. STAUT Transmit RTP1_BE, RTP2_VI,Receive RTP3_BE
- Record rx throughput of RTP1_BE	Pass
- Record rx throughput of RTP2_VI	Pass
- Record tx throughput of RTP3_BE	Pass
7. STAUT Transmit RTP1_BK, RTP2_BE,Receive RTP3_BK
- Record rx throughput of RTP1_BK	Pass
- Record rx throughput of RTP2_BE	Pass
- Record tx throughput of RTP3_BK	Pass
8. STAUT Transmit RTP1_VI, RTP2_VO,Receive RTP3_VI
- Record rx throughput of RTP1_VI	Pass
- Record rx throughput of RTP2_VO	Pass
- Record tx throughput of RTP3_VI	Pass
5.3:Traffic differentiation in single BSS: 1 WMM AP and 1 WMM STA, and 1 WMM STAUT
5.3.3.1 Configuration of WMM-S3-NoSecurity
1. Verify Beacon frame	Pass
2. If a Probe Request occurs and STAUT Probe Request contains any WMM element, FAIL	Pass
3. If STAUT Association Request contains WMM information element AND STA Associated, PASS	Pass
4. STAUT Transmit RTP1_BE,STA2 Transmit RTP2_VI RTP3_BE
- Record rx throughput of RTP1_BE	Pass
- Record rx throughput of RTP2_VI	Pass
- Record rx throughput of RTP3_BE	Pass
5. STAUT Transmit RTP2_VI,STA2 Transmit RTP1_BE RTP3_BE
- Record rx throughput of RTP2_VI	Pass
- Record rx throughput of RTP1_BE	Pass
- Record rx throughput of RTP3_BE	Pass
6. STAUT Transmit RTP1_BK,STA2 Transmit RTP2_BE RTP3_BK
- Record rx throughput of RTP1_BK	Pass
- Record rx throughput of RTP2_BE	Pass
- Record rx throughput of RTP3_BK	Pass
7. STAUT Transmit RTP1_VI,STA2 Transmit RTP2_VO RTP3_VI
- Record rx throughput of RTP1_VI	Pass
- Record rx throughput of RTP2_VO	Pass
- Record rx throughput of RTP3_VI	Pass
5.3.3.2 Configuration of WMM-S3-WEP
1. Verify Beacon frame	Pass
2. If a Probe Request occurs and STAUT Probe Request contains any WMM element, FAIL	Pass
3. If STAUT Association Request contains WMM information element AND STA Associated, PASS	Pass
4. STAUT Transmit RTP1_BE,STA2 Transmit RTP2_VI RTP3_BE
- Record rx throughput of RTP1_BE	Pass
- Record rx throughput of RTP2_VI	Pass
- Record rx throughput of RTP3_BE	Pass
5. STAUT Transmit RTP2_VI,STA2 Transmit RTP1_BE RTP3_BE
- Record rx throughput of RTP2_VI	Pass
- Record rx throughput of RTP1_BE	Pass
- Record rx throughput of RTP3_BE	Pass
6. STAUT Transmit RTP1_BK,STA2 Transmit RTP2_BE RTP3_BK
- Record rx throughput of RTP1_BK	Pass
- Record rx throughput of RTP2_BE	Pass
- Record rx throughput of RTP3_BK	Pass
7. STAUT Transmit RTP1_VI,STA2 Transmit RTP2_VO RTP3_VI
- Record rx throughput of RTP1_VI	Pass
- Record rx throughput of RTP2_VO	Pass
- Record rx throughput of RTP3_VI	Pass
5.3.3.3 Configuration of WMM-S3-WPA
1. Verify Beacon frame	Pass
2. If a Probe Request occurs and STAUT Probe Request contains any WMM element, FAIL	Pass
3. If STAUT Association Request contains WMM information element AND STA Associated, PASS	Pass
4. STAUT Transmit RTP1_BE,STA2 Transmit RTP2_VI RTP3_BE
- Record rx throughput of RTP1_BE	Pass
- Record rx throughput of RTP2_VI	Pass
- Record rx throughput of RTP3_BE	Pass
5. STAUT Transmit RTP2_VI,STA2 Transmit RTP1_BE RTP3_BE
- Record rx throughput of RTP1_BE	Pass
- Record rx throughput of RTP2_VI	Pass
- Record rx throughput of RTP3_BE	Pass
6. STAUT Transmit RTP1_BK,STA2 Transmit RTP2_BE RTP3_BK
- Record rx throughput of RTP1_BK	Pass
- Record rx throughput of RTP2_BE	Pass
- Record rx throughput of RTP3_BK	Pass
7. STAUT Transmit RTP1_VI,STA2 Transmit RTP2_VO RTP3_VI
- Record rx throughput of RTP1_VI	Pass
- Record rx throughput of RTP2_VO	Pass
- Record rx throughput of RTP3_VI	Pass
5.3.3.4 Configuration of WMM-S3-WPA2
1. Verify Beacon frame	Pass
2. If a Probe Request occurs and STAUT Probe Request contains any WMM element, FAIL	Pass
3. If STAUT Association Request contains WMM information element AND STA Associated, PASS	Pass
4. STAUT Transmit RTP1_BE,STA2 Transmit RTP2_VI RTP3_BE
- Record rx throughput of RTP1_BE	Pass
- Record rx throughput of RTP2_VI	Pass
- Record rx throughput of RTP3_BE	Pass
5. STAUT Transmit RTP2_VI,STA2 Transmit RTP1_BE RTP3_BE
- Record rx throughput of RTP2_VI	Pass
- Record rx throughput of RTP1_BE	Pass
- Record rx throughput of RTP3_BE	Pass
6. STAUT Transmit RTP1_BK,STA2 Transmit RTP2_BE RTP3_BK
- Record rx throughput of RTP1_BK	Pass
- Record rx throughput of RTP2_BE	Pass
- Record rx throughput of RTP3_BK	Pass
7. STAUT Transmit RTP1_VI,STA2 Transmit RTP2_VO RTP3_VI
- Record rx throughput of RTP1_VI	Pass
- Record rx throughput of RTP2_VO	Pass
- Record rx throughput of RTP3_VI	Pass
5.4 Traffic differentiation in single BSS: 1 AP and 1 WMM STAUT and 1 legacy STA
1. Verify Beacon frame	Pass
2. If a Probe Request occurs and STAUT Probe Request contains any WMM element, FAIL	Pass
3. If STAUT Association Request contains WMM information element AND STA Associated, PASS	Pass
4. STAUT Transmit RTP1_BE RTP2_VI,STA2 Transmit RTP2_VI RTP3_BE
- Record rx throughput of RTP1_BE	Pass
- Record rx throughput of RTP2_VI	Pass
- Record rx throughput of RTP3_BE	Pass
5. STAUT Transmit RTP2_VI,STA2 Transmit RTP1_BE RTP3_BE
- Record rx throughput of RTP1_BE	Pass
- Record rx throughput of RTP2_VI	Pass
- Record rx throughput of RTP3_BE	Pass
6. STAUT Transmit RTP1_BE,Receive RTP2_VI,STA2 Transmit RTP3_BE
- Record rx throughput of RTP1_BE	Pass
- Record tx throughput of RTP2_VI	Pass
- Record rx throughput of RTP3_BE	Pass
5.5 Test of ACM bit conformance (WMM-S5)
1. Verify Beacon frame	Pass
2. Probe Request occurs	Pass
3. Association Request	Pass
4. STAUT Transmit RTP2_VI RTP3_BE,STA2 Transmit RTP1_BE
- Record rx throughput of RTP1_BE	Pass
- Record rx throughput of RTP2_VI	Pass
- Record rx throughput of RTP3_BE	Pass
5.6 Test of AC Parameter Modification (WMM-S6)
1. Verify Beacon frame	Pass
2. Probe Request occurs	Pass
3. Association Request	Pass
With modified AC parameters:
4. STAUT Transmit RTP2_VI RTP3_BE,STA2 Transmit RTP1_BE
- Record rx throughput of RTP1_BE	Pass
- Record rx throughput of RTP2_VI and verify that RTP2 is 85% or less value of RTP1 or RTP3	Pass
- Record rx throughput of RTP3_BE	Pass
With modified AC parameters restored to defaults:
5. STAUT Transmit RTP2_VI RTP3_BE,STA2 Transmit RTP1_BE
- Record rx throughput of RTP1_BE	Pass
- Record rx throughput of RTP2_VI and verify that RTP2 is 115% or more the value of RTP2 above	Pass
- Record rx throughput of RTP3_BE	Pass
5.7 TXOP Limit Test (WMM-S7)
1. Set TXOPlimit: AC_VI = 0 (1 frame) on AP
STAUT Transmit RTP1_VI,STA2 Transmit RTP2_BE
- Record rx throughput of RTP1_VI	Pass
- Record rx throughput of RTP2_BE [RTP1/RTP2 <=177%]	Pass
2. Set TXOPlimit: AC_VI = 24 (768 µS) on AP
STAUT Transmit RTP1_VI,STA2 Transmit RTP2_BE
- Record rx throughput of RTP1_VI	Pass
- Record rx throughput of RTP2_BE [RTP1/RTP2 <=217%]	Pass
3. Set TXOPlimit: AC_VI = 34 (1088 µS) on AP
STAUT Transmit RTP1_VI,STA2 Transmit RTP2_BE
- Record rx throughput of RTP1_VI	Pass
- Record rx throughput of RTP2_BE [RTP1/RTP2 <=220%]	Pass
5.8 Interworking with legacy Infrastructure: 1 Legacy AP and 1 WMM STAUT and 1 legacy STA (WMM-S8)
1. Verify Beacon frame	Pass
2. Probe Request occurs	Pass
3. Association Request	Pass
4. STAUT Transmit RTP2_VI ,STA2 Transmit RTP1_BE,RTP3_BE
- Record rx throughput of RTP1_BE	Pass
- Record rx throughput of RTP2_VI [6.9]	Pass
- Record rx throughput of RTP3_BE	Pass
5.9 Test of STAUT “No Acknowledgement” (WMM-S9)
1. Verify Beacon frame	Pass
2. Probe Request occurs	Pass
3. Association Request	Pass
4. STAUT Receive RTP1_BE,RTP2_VI
- Record tx throughput of RTP1_BE	Pass
- Record tx throughput of RTP2_VI	Pass
5 Configure the testbed AP to set the “ack policy” field to “012” (no acknowledgement) in QoS Control frames for all AC, STAUT Receive RTP1_BE,RTP2_VI
- Record tx throughput of RTP1_BE{should be > from step 4]	Pass
- Record tx throughput of RTP2_VI {should be > from step 4]	Pass

WPA2 802.11a/g Test Results

WiFi 802.11 a/g + WPA2 System Interoperability Test Matrix


5.1.1 OOB Verification	Pass
5.1.2 STA Initial Ping Interoperability Test
- Cisco (AP1)	Pass
- Broadcom (AP2)	Pass
- Atheros (AP3)	Pass
- Instant 802 (AP4)	Pass
5.2.2.1 Configuration #S1 -- Cisco AP
- Data Transfer 2: FileSendLong Rx - S1DT2[14.5]	Pass
- Data Transfer 3: InquiryLong Tx - S1DT3[0.89]	Pass
5.2.2.2 Configuration #S2 --Broadcom AP
- Data Transfer 1: FileSendLong Tx - S2DT1[10.4]	Pass
- Data Transfer 3: InquiryLong Tx - S2DT3[0.87]	Pass
5.2.2.3 Configuration #S3 -- Atheros AP
- Data Transfer 1: FileSendLong Tx - S3DT1[7.6]	Pass
- Data Transfer 2: FileSendLong Rx - S3DT2[5.1]	Pass
- Data Transfer 3: InquiryLong Tx - S3DT3[0.73]	Pass
5.2.2.4 Configuration #S4 -- Broadcom AP
- Data Transfer 1: FileSendLong Tx - S4DT1[11.39]	Pass
- Data Transfer 2: FileSendLong Rx - S4DT2 [11.9]	Pass
- Data Transfer 3: InquiryLong Tx - S4DT3[0.73]	Pass
5.2.2.5 Configuration #S5 – Atheros AP - Replay Counter Processing
- Data Transfer 4: InquiryL-Replay Tx - S5DT4[0.84]	Pass
5.2.2.6 Configuration #S6 – Atheros AP
- Data Transfer 1: FileSendLong Tx - S6DT1[14.7]	Pass
- Data Transfer 2: FileSendLong Rx - S6DT2 [15.5]	Pass
- Data Transfer 3: InquiryLong Tx - S6DT3 [0.85]	Pass
5.2.2.7 Configuration #S7 – Instant 802 AP
- Data Transfer 1: FileSendLong Tx - S7DT1[9.95]	Pass
- Data Transfer 2: FileSendLong Rx - S7DT2 [16.1]	Pass
- Data Transfer 3: InquiryLong Tx - S7DT3 [0.80]	Pass
5.3.1 - WPA Same Mode Roaming using Pre-Shared Keys
- Cisco (AP1)	Pass
- Broadcom (AP2)	Pass
- Atheros (AP3)	Pass
5.4.1 Multicast Configuration #MCS1 Cisco AP Values: (ESSID: Multicast,Beacons 100)
- Data Transfer: Realaud Rx	Pass
5.4.1 Multicast Configuration #MCS1 Broadcom AP Values: (ESSID: Multicast,Beacons 100)
- Data Transfer: Realaud Rx	Pass
5.5 STA Pre-authentication and PMK Caching
5.5.1,5.5.2 Pre-authentication Test
- Associate STAUT with either AP and iInitiate a continuous ping from STAUT to the wired network.	Pass
- Power off the AP to which the STAUT is currently associated and verify that the ping resumes within 90 seconds.	Pass
- Wired sniffer capture - Verify that an EAP-Success frame with the ethertype of “pre-authentication” (0x88c7) was sent to the STAUT’s MAC address.	Pass
- Wireless sniffer capture - Verify that a PMKID is included in the association or re-association request from STAUT to AP1	Pass
- Wireless sniffer capture - Verify that the same PMKID is included in message 1 of the 4-way handshake sent by AP1	Pass
- Wireless sniffer capture - Verify that no EAP frames (full 802.1X exchange) are sent from STAUT to AP1 or from AP1 to STAUT.	Pass
5.5.3,5.5.4 PMK Caching Test
- Associate STAUT with either AP and iInitiate a continuous ping from STAUT to the wired network.	Pass
- Force a roaming event for STAUT from the initial AP to second AP in the test bed without clearing the PMK cache on the initial AP(disable radio on the initial AP).	Pass
- Verify STAUT ping resumes within 90 seconds.	Pass
- Force a re-association event for STAUT from the second AP back to the initial AP .	Pass
- Verify in the sniff that a PMKID is included in the association or re-association request from STAUT to initial AP	Pass
- Verify that the same PMKID is included in message 1 of the 4-way handshake sent by the initial AP to the STAUT	Pass
- Verify that no EAP frames (full 802.1X exchange) are sent from STAUT to the initial AP.	Pass
5.6 WPA Specific Countermeasures
- After the first bad frame STA continues to ping for the next 70 seconds	Pass
- After the second bad frame STA continues to ping for the next 50 seconds	Pass
- After the third bad frame STA deauthenticates and pings stop	Pass
- After 60 seconds the STA can associate and the ping session resumes	Pass
5.7 STA WPA2 Negative tests
5.7.1.1 Non-Association with a WEP AP,Instant 802
- Verify the STA does not receive a ping response from the authenticaton server	Pass
5.7.1.2 Non-Association with an AP not using WPA2,Instant 802
- Verify the STA does not receive a ping response from the authenticaton server	Pass
5.7.1.3 WPA-Personal – WPA-Enterprise Rejection
5.7.1.3.1 Non-Association with PSK configured Station
- Verify a reference STA configured for WPA-TLS can associate and can ping the server	Pass
- Verify the STAUT does not receive a ping response from the authenticaton server	Pass
5.7.1.3.2 Non-Association with a TLS configured Station
- Verify the STA does not receive a ping response from the authenticaton server	Pass
- Verify the STA does not receive a ping response from the authenticaton server	Pass

WHQL Test Results

WindowsXP results are based on HCT 12.0.

LogName	Total	Passed	Failed	Warned
2c_rsssendrecv.htm	5	5	0	0
2c_wlan_randomoids.htm	7	7	0	0
1c_rssoids.htm	4	4	0	0
2c_wpa_sendcheck.htm	8	8	0	0
2c_wpa_removekey.htm	10	10	0	0
2c_wpa_infrastructure.htm	6	6	0	0
2c_wpa_bssidlist.htm	7	7	0	0
2c_wpa_authentication.htm	7	7	0	0
2c_wpa_adhoc.htm	7	7	0	0
2c_wpa_addkey.htm	14	14	0	0
2c_wlan_wep.htm	28	28	0	0
2c_wlan_reloaddefaults.htm	19	19	0	0
2c_wlan_adhoc.htm	10	10	0	0
1c_wpa_networktypessupported.htm	6	6	0	0
1c_wpa_encryption.htm	7	7	0	0
1c_wpa_associationinfo.htm	13	13	0	0
1c_wlan_bssid.htm	10	10	0	0
1c_wlan_powermode.htm	16	16	0	0
1c_wlan_networktypeinuse.htm	11	11	0	0
1c_wlan_disassociate.htm	13	13	0	0
1c_wlan_configuration.htm	13	13	0	0
1c_wlan_bssidlist.htm	43	43	0	0
1c_wlan_associatetime.htm	7	7	0	0
1c_wlan_ssid.htm	22	22	0	0
2m_WOLPattern.htm	5	5	0	0
2m_WOLMagicPacket.htm	4	4	0	0
2c_PMStandby.htm	36	36	0	0
2c_PMHibernate.htm	46	46	0	0
2c_TransferData.htm	26	26	0	0
2c_StressClient.htm	18	18	0	0
2c_Simultaneous.htm	31	31	0	0
2c_SendRecv1.htm	409	358	0	51
2c_SendPackets.htm	57	56	0	1
2c_RecvMulticast.htm	182	163	0	19
2c_ReceivePackets.htm	66	66	0	0
2c_Priority.htm	8	8	0	0
2c_PerformanceProfile.htm	32	32	0	0
2c_receivestats.htm	3	3	0	0
2c_PerformanceBlast.htm	16	16	0	0
2c_OffloadCheckSum.htm	4	4	0	0
2c_OffloadLargeSend.htm	4	4	0	0
2c_OffloadTaskMisc.htm	4	4	0	0
2c_LoadUnload.htm	186	186	0	0
2c_Deadlock.htm	11	11	0	0
2c_CheckConnections.htm	11	11	0	0
2c_shortpackets.htm	4	4	0	0
2c_AddressChange.htm	80	80	0	0
1c_SetMulticast.htm	283	283	0	0
1c_SetLookahead.htm	75	75	0	0
1c_Reset.htm	149	149	0	0
1c_OidsNdisRequest.htm	85	83	0	2
1c_OffloadInvalid.htm	4	4	0	0
1c_LoopbackStress.htm	19	19	0	0
1c_LoopbackSend.htm	130	130	0	0
1c_FaultHandling.htm	30	30	0	0
1c_KernelCalls.htm	8	8	0	0
1c_64BitOIDs.htm	11	5	0	6
1c_wlan_mediaevents.htm	13	13	0	0
1c_InitTime.htm	25	24	0	1
2c_MediaCheck.htm	31	29	0	2
WHQLConfigCheck.htm	17	17	0	0
Total	2416	2334	0	82

Windows2000 results are based on HCT 11.2.

08/11/2003 12:29:00 18:23:00 2099 2037 10 52

LogName	Total	Passed	Failed	Warned
2c_PMStandby.htm	26	26	0	0
2c_PMHibernate.htm	35	35	0	0
1c_InitTime.htm	25	25	0	0
2c_MediaCheck.htm	26	25	0	1
1c_wlan_ssid.htm	9	9	0	0
1c_wlan_powermode.htm	4	4	0	0
1c_wlan_associatetime.htm	5	5	0	0
2m_wlan_wep.htm	9	9	0	0
1c_wlan_bssidlist.htm	5	3	2	0
1c_wlan_mediaevents.htm	11	9	0	2
1c_wlan_disassociate.htm	15	15	0	0
2m_WOLMagicPacket.htm	3	2	0	1
2c_TransferData.htm	25	24	0	1
2c_StressClient.htm	17	17	0	0
2c_Simultaneous.htm	30	30	0	0
2c_SendRecv1.htm	408	396	0	12
2c_SendPackets.htm	56	36	0	20
2c_RecvMulticast.htm	182	180	0	2
2c_ReceivePackets.htm	65	63	0	2
2c_Priority.htm	7	7	0	0
2c_PerformanceProfile.htm	31	31	0	0
2c_PerformanceBlast.htm	15	15	0	0
2c_OffloadTaskMisc.htm	4	4	0	0
2c_OffloadLargeSend.htm	4	4	0	0
2c_OffloadCheckSum.htm	4	4	0	0
2c_LoadUnload.htm	164	163	0	1
2c_Deadlock.htm	10	10	0	0
2c_ShortPackets.htm	3	3	0	0
2c_CheckConnections.htm	10	10	0	0
1c_SetMulticast.htm	289	289	0	0
1c_SetLookahead.htm	75	75	0	0
1c_Reset.htm	149	149	0	0
1c_OidsNdisRequest.htm	83	83	0	0
1c_OffloadInvalid.htm	4	4	0	0
1c_LoopbackStress.htm	19	19	0	0
1c_LoopbackSend.htm	130	129	0	1
1c_FaultHandling.htm	30	30	0	0
1c_KernelCalls.htm	8	6	0	2
1c_64BitOIDs.htm	11	5	0	6
2c_AddressChange.htm	73	72	0	1
2m_wlan_adhoc.htm	10	3	7	0
WHQLConfigCheck.htm	10	9	1	0
Total	2099	2037	10	52

What's New in the 3.100.36.0 Release?

Imported New MeetingHouse Supplicant to fix::
- a crash due to debug statements left in build
- an authentication hang when a user password change is requested by the server during EAP-FAST provisioning.

What's New in the 3.100.35.0 Release?

All HTML Translations are final.
Resolved an SSO issue where Simplified Chinese SSID was missing in GINA Wireless Network Status (a Dbl Byte character issue)
Resolved an issue where PEAP-GTC 802.1x CKIP authenticating to FUNK switches between Ass. & Auth.
Resolved an issue where GINA/SSO on a Local Login, Suspend/Resume now handled correctly.
Placed Timeout in Domain validation code within GINA/SSO in case an invalid domain was selected.

What's New in the 3.100.30.0 Release?

Resolved an issue where SSO disassociates after initial authentication (login script/roam profile failure)
Resolved an issue where SSO disassociates after logoff and cannot save a roaming profile
Resolved a LEAP CCX prompt issue for the CCX test plan
Upgraded the "BRCM-NTLOGIN" dialog box.
Resolved an issue where SSO/GINA did not engage after a resume from hibernate

What's New in the 3.100.27.0 Release?

Added a new "BRCM-NTLOGIN" screen when 3rd party GINA software (tested with Novell) exists
With new dialog, .27 now interoperates with Novell and 3rd Party GINA software (we no longer try to grab NT credentials from third party elements)
Resolved a GINA blue screen
Resolved which adhoc network connection icon being displayed after resume from s3/s4 (done in prior release)
SSO now displays branded adapter name in SSO box during login.
Fixed and issue with auth type for EAP FAST. Should be 0x80 not 0x00. Resolved with Cisco. This was not documented in the CCXv3 Spec.

What's New in the 3.100.25.0 Release?

Added a delay for WZC/Tray co-existence configurations to increase the chance of WZC not interfering with the configuration
Fixed an issue where link status shows CH0 when associated to CH165 in Australia/Austria
Modified connect status for AdHoc network to be based on 2nd party link (HCT 12)
Resolved an issue with Quick-Connect allowing PSK networks to be configured
Resolved an issue with the control panel to properly ID a 4318 single band and dualband card.

What's New in the 3.100.24.0 Release?

Implemented power save mode during off channel scans for HCT 12
Limited users now able to change "Let this tool manage your wireless settings" box
Preferred networks export now defaults to file name = bcmpn.wpn
Added Advance tab descriptions to the help file
Re-Enabled Quick Connect
Languaged HTML files are enabled in this build (translations not complete yet)

What's New in the 3.100.22.0 Release?

Resolved an issue where multiple Preferred Networks could be created with the same SSID
Re-fixed an issue where the ICON does not show up in the tray

What's New in the 3.100.21.0 Release?

Completed changes for minimum channels being set for a certain set of countries
Fixed a series of issues for local machine login and SSO GINA support. GINA is now silent in local machine environments
Resolved a tray issue when status changes to Associated after being Authenticated

What's New in the 3.100.20.0 Release?

Fixed an issue with 4318 Bluetooth Co-existence being enabled
Changed the Certificate Dialog box Title (it was 'Dialog')
Resolved an issue where changing source SSID to existing SSID produces error with source PN name
Fixed an SSO blue screen issue
Re-fixed an issue where the ICON does not show up in the tray
Fixed a UI element where the driver improperly reported -10db during initial join/roam events
Resolved an issue where PEAP-GTC using Login/Identity field was used to authenticate instead of prompt
WZC and Tray co-existance has an issue where WZC will still try to configure the driver after being disabled. An enable/disable has been added to the build to relieve users of the WZC system interactions. It can be enabled for those who wish to have 802.1x Ethernet co-exist with wireless 802.1x configurations.

What's New in the 3.100.18.0 Release?

Re-fixed an issue for Control Registers diagnostic fails when associated to 802.11a AP
Fixed an issue where the tray icon would be delayed in getting placed into the tray
Resolved handling hover text status, and the 128 character limit Microsoft imposes
Resolved an issue with TLS on Funk Odyssey Server Fails authentication with the tray, passes w/ WZC
Reduced the possibility of the "30 second" authentication delay from occurring

What's New in the 3.100.16.0 Release?

Fixed an issue where EAP-FAST controls were enabled for LEAP
Fixed an issue where Login/Identity was not populated from Certificate (TLS)
SSO with EAP-FAST Networks now functional

What's New in the 3.100.15.0 Release?

Reached EAP Stability
Single Signon is now enabled for CCXv3
Limited Users can now manipulate machine based preferred networks
Power Save mode on 4318 now operational
TTLS with Funk Odyssey functional when specific issuer is chosen
Channel 165 enabled (incorrectly behind a debug build #ifdef)
WPA not functioning after upgrading to 3.100.8

What's New in the 3.100.11.0 Release?

Added new commands for Installshield to supply an exported preferred network file during install
Added support for simultaneous WZC and BRCM Tray.
Fixed various issues
- Fast User Switching
- WLTRYSRV description missing in Admin tools / Services
- Control Registers diagnostic fails when associated to 802.11a AP
- Increased the timeout for STA WPA to allow for busy environments
- Fixed an issue with WPA/AES/TTLS and blank identity field
- Cannot associate to Cisco 1200 using CCKM

What's New in the 3.100.9.0 Release?

Preferred Networks now have the ability to be locked.
Fixed several bugs
- Resolved CCXv2 Radio Measurement bug
- Fixed a WHQL 1c_kernel calls issue where a debug message got left in the code
- Fixed a preferred networks export issue where the .wpn file could not be saved.
- Fixed a tray issue where multiple Preferred Networks could be created with the same SSID
- Resolved an issue on dualband cards where the network would de-authenticate on heavily congested networks
- Fixed an issue with CCKM Authentication Key Management
- Fixed an issue where the tray icon will disappear "sometimes". This is due to an issue found in the current MeetingHouse supplicant. A new supplicant has been imported for this release.
- Added UI elements for SmartCards.

What's New in the 3.100.8.0 Release?

The tray now allows a user to import and export preferred network profiles.
The tray infrastructure now supports the notion of auto import. If an exported preferred network ("bcmpn.wpn") shows up in the same directory as bcmwltry.exe (%systemdir%\system32\windows) the contents will be automatically imported.
The tray, upon initialization, if configured via the registry (.inf) will inspect Windows Regional settings to set the current country location which in turn defines the regulatory domain settings of the adapter. Note, WindowsXP uses the "Location" field. Win2K uses the "Standards and Format" field. The link status page has been updated to display the current country code.
Channel 165 has been enabled in the driver
EAP-FAST is now enabled in control panel UI.
WPA2,WPA2-PSK are now enabled in the driver and tray
WPA auto with auto cipher selection is now enabled within the driver and tray
CCKM CCXv3 EAP combinations (FAST) are now enabled in the driver and tray
Added support for 4318B0 MPG and MPAGH reference designs
Added support for hover text extensions (was not discussed in 3.100.4 release notes)
Integrated a new MeetingHouse supplicant, version 3.0.1.12
The advance tab for band roaming configuration has been simplified.
Resolved a double byte character set issue for username and password GINA prompts within the tray.

What's New in the 3.100.4.0 Release?

Upgraded MeetingHouse Supplicant to v3.1.0.10. This fixes an issue when after rebooting, you could never complete an 802.1x authentication sequence. Only the initial sequence would work.

What's New in the 3.100.3.0 Release?

Upgraded MeetingHouse Supplicant to v3.1.0.7
Added support for Fast User Switch within the Tray application. wltry.exe is not executing for each user session with it's own copy of the control panel.
Basis for Enterprise release created. WME, WPA2, Tray, and in-driver supplicants formed in a common release
Radio is now turned off when device is not associated and not scan, thus saving power prior to network connectivity. This feature does not conflict with network connectivity.
New roaming functionality has been added. It is now possible to roam to AP in preferred band after non-association scan results are completed.
Added an adaptive roaming algorithm to back off the restrictions in roam targets as network conditions get worse. This helps to maintain connectivity.
New UI elements have been added to the control panel, but are not enabled at this time. This includes EAP-FAST, Import/Export capability, and SmartCard Support
Passive scanning dwell time has been increased in all locales by at least 20%.
Passive scanned channels will now connect to closed networks if the driver sees there are beacons already being sent on that channel, even if it is an 11a radar sensitive channel.

Broadcom 802.11 Wireless Network Drivers Release 3.100.41.0

System Requirements

Software (supports the following operating systems):

Hardware:

Included in This Release

Hardware and Interoperability Test Matrix

Known Limitations, Problems, and Notices

What's New in the 3.100.41.0 Release?

WIFI WPA + 802.11g Test Results

WIFI WPA + 802.11b Test Results

CCX Test Results

WIFI 802.11a + WPA Test Results

WME/WMM 802.11 Test Results

WPA2 802.11a/g Test Results

WHQL Test Results

What's New in the 3.100.36.0 Release?

What's New in the 3.100.35.0 Release?

What's New in the 3.100.30.0 Release?

What's New in the 3.100.27.0 Release?

What's New in the 3.100.25.0 Release?

What's New in the 3.100.24.0 Release?

What's New in the 3.100.22.0 Release?

What's New in the 3.100.21.0 Release?

What's New in the 3.100.20.0 Release?

What's New in the 3.100.18.0 Release?

What's New in the 3.100.16.0 Release?

What's New in the 3.100.15.0 Release?

What's New in the 3.100.11.0 Release?

What's New in the 3.100.9.0 Release?

What's New in the 3.100.8.0 Release?

What's New in the 3.100.4.0 Release?

What's New in the 3.100.3.0 Release?

Broadcom 802.11 Wireless Network Drivers
Release 3.100.41.0